1.(5) The displacement uniformity of re-greasing distributors was researched experimentally, the results showed that the designed displacement of re-greasing distributor is smaller, the actual displacement precision is lower and uniformity is worse;
(5)通过实验方法研究了配油器的排量均匀性,结果表明:标定规格越小的配油器排量精度越低,均匀性越差;
2.Then, through radius determination, outspread of the profile, values calculation and so on, many characteristic values of fabric drape (drape coefficient, number of crest, crest amplitude uniformity, crest angle uniformity, crest amplitude maximum, crest angle maximum and so on) can be measured.
根据织物悬垂图像轮廓信息,经半径确定、轮廓展开和指标计算等步骤,可测得织物悬垂性的多个特征值,如悬垂系数、波数、波峰幅值均匀度、波峰夹角均匀度、最大波峰幅值、最大波峰夹角等。
3.The advice to ventilate surely arises indirectly, from the need to ensure temperature uniformity, and consequent RH uniformity, in all corners of the room.
通风的确可以使室内所有角落的温度和相对湿度都趋于一致。
4.The main results are as follows:1. The Archimedes line is introduced in this paper as the center axes of the pushing processing die, which will reduce the deformation and be prone to the metal flow uniformity from concave to convexity, which can identify the aim of wall thickness uniformity, which can eliminate increase of inner wall thickness and decrease of outer wall thickness in the deformation of pipe bending.
(1)采用阿基米德螺线作为模具扩径变形段的中轴线,有利于管坯变形时金属的流动,使凹面金属充分向凸面流动,从而避免传统弯管工艺变形时内侧增厚,外侧减薄的壁厚不均现象。
5.the cycle life with condition of 1 C rate charge to 80% SOC and 2 C rate discharge to 100%DOD was more than 3 100 cycles,in which the number of cycles with the capacity higher than 40 Ah could reach 2 700,indicated that the cell had good performance of uniformity and excellent ability to keep the uniformity during service;
单体电池1C充电80%SOC、2C放电100%DOD的循环寿命超过3 100次,且在寿命期内,保持容量高于40 Ah的循环次数达2 700次,表明单体电池的一致性和一致性的保持能力好;
6.The influence of aperture angle for illumination light on uniformity of the color splitting system is discussed and a color aberration correction by means of wedge coating with. gradient thickness is proposed, thus the color uniformity can be obviously improved.
讨论了照明光孔径角对分色系统色均匀性的影响,提出了用厚度渐变的楔形膜校正色差的方法,使色均匀性得到显著改进。
7.With FEM analysis ,the melt flow velocity and pressure distribution in the die channel were calculated, and the effect rule of some die structure parameters, such as compression ratio and compression angle, on the extrusion velocity distribution , flow rate, and flow uniformity was analyzed quantitatively. This would lay foundation of optimizing the die channel design and researching on extrusion flow uniformity.
本文采用有限元数值分析方法 ,计算了熔体在口模内流动的速度场和压力场 ,定量分析了压缩比和压缩角等压缩段模具结构参数对挤出速度分布、挤出流量和挤出流动均匀性等的影响规律 ,为优化流道结构参数 ,提高挤出流动均匀性的研究提供了基础
8.Etching experi ments showa good uniformity of ±5.4 %of etching depth over the 40 cm. The uniformity can bei mproved combined with beam revising by beam diaphragm and correction mask.
刻蚀实验表明40 cm长度范围刻蚀深度均匀性为±5.4%,同时具有较好的束流稳定性.
9.Having comprehensively analyzed many experiment results of laser surface alloying and used the mass transfer model by Anthony and Cline, this paper studied the inherent reasons which result in basic composition uniformity of surface alloying macrocosmically and the primary factors which affect composition uniformity.
通过大量的激光表面合金化实验结果的综合分析,采用Anthony和cline提出的对流传质模型,从理论土探讨了产生激光表面合金层宏观上基本均匀的内在原因和影响成分均匀性的主要因素。
10.There is a uniformity of life in Utopia - uniformity of thinking, of ambition, of manners, of dress.
乌托邦里的生活千篇一律:想法、抱负、礼节及穿著都一样。
