1.Using PC standard parallel port to realize serial ISP of AVR, if pin /RESET was connected to the ground, the SPI bus could be used to realize the serial programming.
使用PC标准并口实现AVR单片机串行ISP时,若引脚/RESET接地,则可利用SPI总线实现串行编程。
2.At the same time the clock chip PCF8563 and serial EEPROM chip CSI24C01 with Reset and WDT circuit of I2C bus are used hi the system. They have not only provided the non- volatility data storage area, the supervision ability of power supply and MCU and the RTC, and its I2C bus structure has been simplified the circuit design.
同时在系统中还使用了护C总线结构的时钟芯片PcF8563和内置Reset、wDT电路的串行EEPROM芯片CSI24COI，它们不仅提供了电源和微控制器的监控功能、不挥发性的数据存储区、实时时钟，而且其护C总线结构简化了电路设计。
3.At first,we point out that in the embedded system the power-on reset(POR)circuit of CPU and EPLD should not only satisfied the request of reset time but also offer correct time sequence to make POR step finished when initializing EPLD.
首先介绍了在嵌入式系统中,CPU和可编程芯片上电复位电路不仅要满足复位时间要求,而且还要有正确的时序,保证在对可编程芯片初始化时,该芯片上电复位已经结束。
4.To reset your system, select setup, move the highlight down to reset system
欲重置系统，选择Setup，向下移动亮条至ResetSystem
5.The convertible bond is one of the dey issues of security market in China.This paper aims to make a study of how to price convertible bonds with reset clauses.A dopting the thought of equivalent martingale measure,it transforms the underling asset from risk world to the risk-neutral world and prices the convertible bonds with reset clauses with martingale pricing method in the risk-neutral world.
可转换债券是中国证券市场的热点之一.本文主要研究如何给带有重置条款的可转换债券进行定价.文中采用了等价鞅测度的思想将标的物从风险世界转换到风险中性世界中,然后在风险中性世界中应用鞅评价方法对带有重置条款的可转换债券进行定价.
6.Be sure the RED reset button (High Limit Control) is properly set: push in firmly to reset.
确保红色重置按钮（高温限制控制器）被正确设置：如果需要重置，请使劲按一下重置按钮。
7.Singie-step control mode is employed in the circuit, from the stating up. codes of address and instruction in 18 bit are simultaneously displayed in LED as every instruction is implemented by a computer to check if the data bus and address bus are reset for the computer system after CPU is reset, thus failure detection is conducted on the computer system.
电路采用单步控制方式,从开机起,每执行一条指令,就把地址和指令代码用16进制一同显示在LED上,以达到检查CPU在复位后计算机系统数据总线和地址总线是否复位,进而对微机系统总线故障进行测试。
8.The designs of a 8421BCD code up counter and a single pulse generator show that the circuit realization of sequential systems using neighbouring control set and reset is particularly simple. It indicates that the design method of sequential systems using neighbouring control set and reset has advantages and practical significance.
过8421BCD码加法计数器以及单脉冲发生器的设计,证明了采用邻控式置位复位的时序系统的线路比较简单,从而表明采用邻控式置位复位的时序系统设计方法具有一定的优点与实用意义。
9.Also chips on cartridge must " auto-reset" so that no reset device is required.
同样弹夹上的芯片必须是“自动重置”，因此就需要无重置装置。
10.Use a ball-point pen or similar to push the Reset button on the unit. When you press the Reset button, the system becomes operative.
使用圆珠笔或类似物体按本机的重设按钮。当按下重设按钮时，系统可以操作。
