1.TECHNIQUES FOR USING CHINESE CHARACTERS IN DEBUG.COM
DEBUG.COM程序的汉化技术
2.This paper firstly narrates the significance and the goal of developing high-level-symbol debugger, introduces the technology of high-level-symbol debuggingand the working principle of VAX DEBUG, then generally discusses the problem in devel-oping Ada Source DeBugger (ASDB), lastly introduces the implementing situation of thefirst ASDB.
本文首先叙述了开发高级符号调试器的意义和目的,介绍了高级符号调试技术及VAX DEBUG的工作原理,然后就Ada源程序调试器(简称ASDB)的开发问题作了一般讨论,最后介绍了第一版ASDB的实现情况。
3.STRENGTHEN DYNAMIC TRACE FUNCTION OF DEBUG.COM
增强DEBUG.COM的动态跟踪功能
4.The core component of the system is a CPLD, based on which the A/D control logic, UART serial logic, EMIF interface logic, and DEBUG logic are implemented.
系统采用Altera公司的复杂可编程逻辑器件CPLD作为控制核心，实现了A／D芯片的控制时序逻辑、UART串口时序逻辑、系统与DSK的EMIF接口逻辑以及供调试用的DEBUG逻辑。
5.This paper gives the significance and merits of a high-level symbol debugger, principle of VAX debug, and the development and implementation of Ada debugger (ADB)
本文首先叙述开发高级符号调试器的意义和目的,介绍高级符号调试技术及VAX DEBUG的工作原理,然后就Ada语言调试器(简称ADB)的开发问题作一般讨论,最后介绍ADB的实现情况. ＊
6.Analysing Intel 8086/8088 Instruction System from the DEBUG of IBM—PC DOS
用IBM—PC DOS的DEBUG分析INTEL 8086/8088指令系统
7.This paper introduces an experimental method using computer graphic simulation to debug PLC control system,which can make the debug prcedure fo the whole control system illustrative,conveninet economical and practical.
介绍了一种利用计算机图形仿真的实验方法来调试PLC控制系统，使得整个控制系统的调试过程直观、方便、经济实用。
8.4、We set up PROFIBUS-DP Master/Slave test and debug system based oncomputer, use serial debug software simulation the data interchange from industrial process control system to RS232/PROFIBUS-DP Slave Interface, we realized two-way data communication finally through configuration Master and Slave in SOFTPLC, write GSD file and STEP7 communication program by myself design .
4、搭建了基于PC的PROFIBUS-DP主从站试验调试系统,用串口调试软件模拟了生产现场设备接入开发的从站接口。 在SOFTPLC中组态主从站,加入自主开发的GSD文件、STEP7通信程序最终实现了主-从站的双向数据通信,从而验证了论文的设计。
9.This paper adopts DSP+ARM embedded processor TMS320VC5471 EVM as target board to develop embedded integrate development environment based on GDB.First, the debug environment is configured with the debug tool-GDB of the GNU free software.
本课题以DSP+ARM结构的嵌入式处理器TMS320VC5471评估板(EVM)作为目标板，开发了基于GDB的嵌入式系统集成开发环境。 首先采用源代码公开的GNU软件配套调试工具GDB来配置主机的调试环境。
10.The controller software adopts modular structure based on "SCR fire pulses control platform"Finally, the author makes some introduction on debug method, debug question and its answer in the engineering design of FCL and the measure of limiting those disturbances.
考虑控制系统要满足固态限流器不同运行工况的需要，其控制软件要求具有实时性好、可靠性高、灵活性强等特点，控制系统软件采用基础层+功能层的模块化结构设计方案。
