1.For band-pass,the highest code element rate is 2W Baud,and the gettable highest rate of frequency band is 2 Baud/Hz.
对于带通系统而言,最高码元速率为2W Baud,此时可获得的最高频带利用率为2Baud/Hz。
2.The mode of serial communication and the calculating expressions of their baud rate between MCS51/96 single chip computer and microcomputer are expatiated in this paper The permitted error of baud rate is deduced On the condition of the permitted error of communication baud rate, the highest baud rate coefficient of serial communication between MCS51/96 single chip computer and microcomputer are calculated, and the program written by C language is given
阐述了 MCS5 1和 MCS96系列单片机与 PC微型计算机间串行通信模式及其波特率计算式 ,推导了两机通信时波特率误差的允许范围值 ,利用反推法 ,在满足通信波特率误差的允许值前提下 ,计算了 MCS5 1/ 96系列单片机与 PC微机最高串行通信速率的波特率因子 ,并给出了具体实现的 C程序代码
3.This paper first introduces the characteristics of baud rate setting in serial communication of MCS-51 single chip computer, and then mainly analyzes the error of baud rate setting, the origin of baud rate setting and the formulae of computing error of baud rate setting and finally an application example is given.
该文首先介绍了MCS -5 1单片机串行通讯波特率设置的特点 ,然后着重分析了波特率设置的误差 ,得出波特率设置的误差来源和计算波特率误差的相应公式 ,最后给出一个应用的实例。
4.This article introduces the define principle and method of the baud rate of serial communication between PC and single chip microcomputer,and gives the computional method for standard baud rate and unstandard baud rate.
详细论述了单片机与 PC机串行通信中波特率的确定原则和方法 ,特别给出了 PC机与单片机串行通信中非标准波特率的计算方法及不同环境下实现的实例
5.This paper firstly presents the methods of baud rate setting of MCS-51 single-chip computer in serial communication, then analyses the error sources of baud rate, and give several ways for eliminating the error of baud rate.
本文作者首先介绍了MCS 51单片机串行通讯中波特率的设置方法,然后分析了波特率的误差来源,并着重介绍了几种波特率误差的消除方法。
6.First this article take example by MCS-51, analyses the error source of baud rate and the allowable baud rate error, then introduces a method of baud rate autoregulation.
本文首先以MCS-51为例,分析了波特率的误差源和允许的波特率误差,然后介绍了一种自动调整波特率的方法。
7.The research on the baud rate estimation for MPSK/MQAM signals using CZT shows that the proposed estimation algorithm can obtain a baud rate value with a short observation interval.
在参数估计中，主要讨论了利用CZT(线性调频Z变化)在较短的观测长度下对MPSK／MQAM信号波特率进行估计的方法。
8.What baud rate, or range of baud rates, is supported?
是否支持波特率或波特率的范围？
9.The error code trasfer produced by baud rate error in computer asynchronous serial communication is analysed and calculated in this paper,On this basis the permissible limit of the baud rate error is enacted.
本文对计算机异步串行通信中因波特率误差产生错码传输进行分析、计算,总结出波特率误差允许范围。
10.and the baud rate is 2Mb/s at the opposite direction. The baud rate will meet the communicating demand of the CT.
下行光纤通信速率更是高达2Mb/s,完全满足互感器通信需要。
