1.Their parameter valus are δ_1=0.706-1.03,SK_1=0-00.8,Kg=1-1.06.Most of the longest axes(a-axes)of gravelsare parallel to the direction of lake shore zone,and ab-planes of grav-eis dip to lake direction at average angle about 8°.
δ_1=0.706—1.03,SK_1=0—0.08,Kg=1.00—1.06.大多数砾石的长轴(a—axes)平行于湖岸方向排列; ab 面向湖倾斜,平均倾角8°左右.
2.Consider three mutually perpendicular coordinate lines( the -, -,and -axes ) with their zero point at a common point ,called the origin.The three axes form the right-handed system,that is,if the fingers of the right hand are curled so that they curve form the positive - axes toward the positive - axes ,the thumb points in the direction of the positive -axes .
空间中三条相互垂直的坐标线,它们的零点相互重合,称为原点,记为.坐标轴遵循右手法则,即以右手握住-轴,当右手的四个手指从正向-轴以角度转向-轴时,大拇指的指向就是-轴的正向.
3.The directions of P-axes from the western area to the southeastern area changed from N40°E to N90°E step by step. The horizontal directions of P-axes are vertical to the northeast edge of Tibet Plateau, and the elevation angles of P-axes are less than 30°.
结果表明,由甘肃西部到东南部,主压应力方向由北40°东逐渐变为北90°东,P轴仰角大多小于30°,其水平方向垂直于青藏高原东北边缘。
4.Experimental results show that this method can extract the axes of the axes symmetry object effectively in high precision,and the mean error of the axes angle is 0.022°.
实验表明:该方法能够有效地、高精度地提取轴对称目标的中轴线,提取的中轴线平均角度误差为0.022°。
5.3. The axes failure reason of LH------400/13 Copper wire drawingmachine was analyzed, and effective measure are adopt to reduce axes failure.
3.通过分析LH—400/13型铜拉丝机断轴故障的原因,采取有效措施降低了断轴故障率。
6.Results show that with the increase of eccentricity between reaming tool axes and well bore axes,or with the decrease of reamer wing number,the actual pervious radius of reamed borehole will reduce gradually,while the maximal contact force between reamer wing and borehole wall will increase simultaneously. The simulation results present practical and applicable proposition.
仿真结果表明,随着随钻扩眼工具轴心偏离井眼轴心距离的增大,或扩眼刀翼数量的减少,所扩井眼的实际可通过半径逐渐减小,扩眼刀翼与井壁的最大接触力则逐渐增大,据仿真结果给出了实际可用的建议。
7.The result indicates that for the 4 segments the maximum and minimum compressive principal stress axes are all horizontal, while the maximum compressive principal stress axes take approximately the azimuths between N15°E to N30 °E.
结果表明,四个区段的最大和最小主压应力轴皆水平,最大主压应力轴方位大致在 N15°E 至 N30°E 之间.
8.DNC 60GS For shears with max.4 axes, The for this application specific software controls all the typical functions for this machine such as Xbackgauge,X1-X2frontgaugrs,free axes(feeding,evacuator,etc),blade gap,rake angle.cutting depth,etc.
用于带有最多4轴的剪床,对于该数控的使用,其特殊软件种植了该机床的所有典型功能,例如X后挡,X1-X2前挡,自由轴(给料,撤料等),刀口间隙,剪切角度,切割深度等.
9.There is angular between the longer axes of the ellipse and the axes of the shaft, moreover, the angular is variable with the magnitude and the direction of the load.
本文证明该椭圆长轴和传动轴应该呈一定的夹角，而且夹角值随工作载荷的大小和方向的变化而变化。
10.Below the depth of 200 km, the P axes are nearly close to the subducting direction. In he Sea of Okhotsk, above 114 km, the T axes coincide with subducting direction;
两俯冲带在浅部及深部地震密集,100—200km深度之间有双地震层.
